Visit Url

 

 

The publisher is making a number of good points on the subject of Tools You Need to Install a New Bathtub as a whole in this post which follows.

Installing a bathtub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a new one is also a moderately challenging job. If the old tub is readily available, the project can move quickly; if you need to open up a wall surface to eliminate the old bathtub as well as position the new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as embeded in the new one. Make certain you have certified on your own for the job and fit attempting it. Rather than employing a professional to take control of a halfway-completed job, it is far better to consider employing one prior to you begin. Possibilities are you might need a professional plumber to make tube connections.
This post will certainly assist you install a brand-new tub in your restroom if you have currently purchased a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools and also material list need to make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Installment

First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Making use of the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the tub till the spirit level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also check all joints as well as new pipework for leakages and also tighten them if essential. Load the bathtub as well as also check the overflow electrical outlet and the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub ought to wait up until the bathtub has been utilized at the very least when as this will certainly resolve it into its final position.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in location in between the tap as well as the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type needs to be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or water-proof adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you appreciate reading about Installing A Bathtub? Try to leave a remark down the page. We will be delighted to see your opinions about this article. We hope that you come back again in the near future. Are you aware of another person who is enthusiastic about the subject? Feel free to promote it. Thanks so much for taking the time to read it.

Schedule